Monday to Saturday - 8:00 -17:30

If your Rav4 is having difficulties starting up, it may be time for a reset. Here’s how to do it: First, disconnect the negative battery cable and wait about 10 minutes. Next, reconnect the cable and start the engine.
If the engine still won’t turn over, try depressing the accelerator pedal while turning the key. If that doesn’t work, check to see if there’s any corrosion on the battery terminals. If so, clean them off and try again.
Finally, if none of these methods work, you may need to replace your starter.
Are you looking for a way to reset your Rav4 computer? If so, there are a few things you need to know. First, there is no one-size-fits-all solution for this problem.
Second, the process can be different depending on the year and model of your Rav4. Finally, you should only attempt to reset your computer if you are absolutely sure that it is necessary and you know what you’re doing.
If you have determined that resetting your Rav4 computer is the best course of action, there are a few different ways to go about it.
One option is to disconnect the battery for several minutes and then reconnect it. This will usually clear any stored codes or data and allow the computer to start fresh. Another option is to use a special diagnostic tool to connect to the computer and reset it manually.
This method may be more complicated and time consuming, but it will ensure that the job is done correctly.
Regardless of which method you choose, remember that resetting your Rav4 computer can be a delicate operation. Be sure to follow all instructions carefully and consult with an expert if necessary before proceeding.
Como resetear el computador del vehículo sin scaner.
2002 Toyota Rav4 Ecu Reset
If your Toyota RAV4 is having trouble starting up, or if you’re noticing unusual engine behavior, it may be time for an ECU reset. This process is relatively simple and can be done at home with just a few tools.
Before you begin, make sure that your RAV4 has a fully charged battery.
You’ll also need access to a OBD-II scanner/reader in order to connect to the vehicle’s onboard computer. Once you have these things ready, follow these steps to reset the ECU:
1) Locate the “diagnostic” connector under the dash on the driver’s side of the RAV4.
It should have two rows of four pins each.
2) Using your OBD-II scanner/reader, connect to the diagnostic connector and turn on the power.
3) Press and hold the “reset” button on your OBD-II scanner/reader for about five seconds.
This will initiate the ECU reset procedure.
4) After the procedure is complete, disconnect your OBD-II scanner/reader from the diagnostic connector and turn off the power. Start up your RAV4 as normal and see if there are any improvements in performance.

Credit: www.myairbags.com
¿Cómo Resetear Mantenimiento Rav4 Después Del Cambio De Aceite?
If you need to reset the maintenance light on your Rav4 after an oil change, there are a few different ways to do it. One way is to simply disconnect the battery for a few minutes and then reconnect it. This will cause the computer to reset and the light should go off.
Another way is to use a scan tool to access the computer and manually reset the maintenance light.
¿Qué Aceite Lleva Rav4 2012?
There are a few different types of oil that can be used in a 2012 Rav4, but the most common type is 5W-30. This oil is typically used in vehicles that operate in colder climates, as it has a lower viscosity and will flow more easily when the engine is cold. 5W-30 oil also provides good protection against wear and tear, making it a good choice for a vehicle that sees regular use.
Conclusion
If your Rav4 computer is acting up, you can try resetting it. To do this, first turn off the computer. Next, unplug the power cord from the computer and then plug it back in.
Once you’ve done this, turn on the computer and see if it’s working properly again. If not, you may need to take it to a technician for further diagnosis.