Assuming you would like a blog discussing the process of resetting the oil maintenance light on a 2011 Prius:
The oil maintenance light on a 2011 Prius needs to be reset under certain conditions. These conditions include: after an oil change, if the engine is replaced, or if the 12-volt battery is disconnected.
The process to reset the light is not difficult, but it must be done correctly in order to avoid damaging the car.
If you own a 2011 Toyota Prius, you may be wondering how to reset the oil maintenance light. The process is actually quite simple and can be done in just a few minutes. Here’s what you need to do:
1. Start the engine and let it idle for a few minutes.
2. Turn off the engine and open the hood.
3. Locate the oil filter cap on the driver’s side of the engine compartment and remove it.
4. Using a funnel, add fresh oil to the filter housing until it reaches the full mark on the dipstick. Be sure to use the correct type of oil as specified in your owner’s manual.
5. Replace the filter cap and close the hood.
reset 2011 Toyota Prius Oil Maintenance Required Light
Prius Oil Maintenance Reset 2010
If you own a 2010 Prius, you may be wondering how to reset the maintenance required light. The process is actually quite simple and can be done in just a few steps.
First, locate the button on the dash that says “MAINT REQD.”
This stands for Maintenance Required. Press and hold this button for about 5 seconds until the light on the dash begins to blink. Once it starts blinking, release the button and your maintenance light will be reset!
It’s important to keep up with regular maintenance on your Prius, as it helps to keep the vehicle running smoothly and efficiently. So if your light comes back on after a few weeks or months, make sure to take it in for service.
Credit: erwinsalarda.com
How Do You Reset the Oil Maintenance Light on a Toyota Prius?
Assuming you would like a blog post discussing resetting the oil maintenance light on a Toyota Prius:
“How do you reset the oil maintenance light on a Toyota Prius?”
If you need to reset the oil maintenance light on your Toyota Prius, it’s actually a pretty simple process.
All you need is a paper clip! Here’s how to do it:
First, find the odometer reading button on your dash.
It should be located near the speedometer. Press and hold this button for about five seconds.
Next, while still holding down the odometer reading button, turn on your ignition (but don’t start the car).
Continue to hold both down for about another five seconds.
After that, release the button and turn off your ignition. The oil maintenance light should now be reset!
How Do You Reset the Maintenance Light on a 2011 Toyota?
If you need to reset the maintenance light on your 2011 Toyota, there are a few different ways to do it. One way is to disconnect the negative battery terminal for about five minutes, then reconnect it and start the car. This should reset the light.
Another way is to use a scanner tool to clear the code that is causing the light to come on. You can also take your car to a dealership or mechanic and have them reset it for you.
How Do You Reset the Oil Maintenance Light on a 2010 Toyota Prius?
If you need to reset the oil maintenance light on your 2010 Toyota Prius, there are a few different ways that you can do so. One way is to simply disconnect the battery for about 30 seconds and then reconnect it. This will cause the light to reset itself.
Another way is to use a code reader or scan tool to clear the codes that are stored in the vehicle’s computer memory.
How Do You Reset the Maintenance Light on a 2011 Prius V?
The maintenance light on your 2011 Prius V can be reset by following these simple steps:
1. Press and hold the power button for 3 seconds to turn off the power.
2. Insert the key into the ignition and turn it to the “On” position without starting the engine.
3. Press and release the power button twice quickly. The maintenance light will flash and then stay on solid to indicate that it has been reset.
Conclusion
Assuming you would like a summary of the blog post found at the link below:
2011 Prius Oil Maintenance Reset
If you own a 2011 Toyota Prius and need to reset the maintenance light after an oil change, this guide will show you how.
The process is simple and only takes a few minutes.
First, turn on the ignition but do not start the engine. Then press and hold the trip meter reset button for about 5 seconds until the maintenance required light comes on.
Next, press and release the button again and hold it down for another 5 seconds. Finally, turn off the ignition and then restart it to confirm that the light has been reset.
