The 2005 Prius brake light bulb is an important safety feature on your vehicle. It is located in the center of the rear window, and it helps other drivers see your brake lights when you are stopping. If this bulb burns out, it needs to be replaced as soon as possible.
If you own a 2005 Prius, you may have noticed that your brake light bulb is burned out. Replacing the bulb is easy and only takes a few minutes. Here’s how to do it:
First, open the trunk and locate the brake light assembly. There are two screws holding it in place – remove these with a screwdriver. Next, disconnect the electrical connector from the back of the assembly.
Now, twist out the old bulb and insert a new one in its place. Be sure to insert it with the correct orientation – the “+” side should be facing up. Finally, reconnect the electrical connector and reattach the assembly to the trunk lid with the screws.
Toyota Prius Tail Light Turn Signal Light Brake Light Bulb Replacement 2004 – 2009
2005 Prius Brake Light Not Working
If you own a 2005 Prius, you may have noticed that the brake light isn’t working. This is a common problem with this model year and can be easily fixed.
The first thing you’ll want to do is check the fuse.
The fuse for the brake light is located in the engine compartment, on the driver’s side. If this fuse is blown, it will need to be replaced. Next, you’ll need to check the bulbs themselves.
The brake light bulbs are located in the rear of the car, near the taillights. If they are burned out, they will need to be replaced.
This is a more complex repair and will require some disassembly of the car. However, it’s still a relatively easy fix that most people can do themselves. Hopefully this information helps get your brake light working again!
How Do You Change a Brake Light on a 2005 Prius?
Assuming you need to replace a burnt out brake light:
For a 2005 Toyota Prius, open the trunk and locate the two fasteners near the top on either side. These are called T30 Torx screws.
Use a Torx driver or bit to remove these screws (you may need a helper to hold the light assembly in place while you do this). Pry off the black plastic lens cover being careful not to break it and set it aside. The bulb is behind this cover and can now be removed by gently pulling it straight out.
There are three wires attached to the back of the brake light bulb- one yellow, one black, and one green with a white stripe. You will need to disconnect all three of these wires before removing the old bulb completely. To connect the new brake light bulb, simply reverse these steps.
Push the new bulb into place making sure that all three wires are properly connected before snapping on the lens cover and reinstalling the T30 Torx screws.
Which Bulb is the Brake Light Bulb?
There are two brake light bulbs on most vehicles. One is located in the center of the vehicle and the other is located at the outer edge of the vehicle. The center bulb is usually the brake light bulb.
How Do You Change a Prius Brake Light?
If you need to change the brake light on your Prius, it’s a pretty simple process. Here’s what you’ll need to do:
1. Pop the hood and locate the brake light assembly.
It will be mounted on the underside of the spoiler near the center of the car. 2. Use a Phillips head screwdriver to remove the two screws that secure the assembly in place. 3. Carefully pull out the old bulb and insert a new one in its place.
Make sure that the new bulb is seated correctly and screwed in tight before moving on. 4. Replace the entire assembly and screw it back into place using your Phillips head screwdriver. 5. Close up the hood and you’re all done!
How Much Does It Cost to Replace a Prius Tail Light?
Assuming you need to replace just the tail light and not the entire assembly, it would cost anywhere from $75-$200. This cost will depend on the year, make, and model of your car as well as the type of tail light (LED, Xenon, etc.)
If you need to replace the entire assembly, which includes the brake light, turn signal, and reverse lights, then the cost can range from $250-$600.
Again, this will depend on your car’s make and model. It is always best to consult with a certified mechanic or dealer to get an accurate estimate for replacement parts and labor.
If you’re driving a 2005 Prius and your brake light bulb burns out, don’t panic! Replacing the bulb is actually a pretty simple process. Just follow these steps and you’ll have your brake light back in no time:
1. First, open up the trunk of your Prius. There are two access panels on either side of the trunk that you’ll need to remove in order to get to the bulbs. 2. Once you have access to the bulbs, twist counterclockwise to loosen and remove the old bulb.
3. Now it’s time to install the new bulb! Just insert it into the socket and twist clockwise until it’s tight. 4. Finally, replace the access panels and close up the trunk.
And that’s it – you’re all set!